topblog Ivoire blogs


ECM calibration download for Cummins Insite software

This is a copy version of installation help of Cummins Insite ECM calibration. Credits to the O.P. it’s sourced

Please note that not all subscription types will have access to calibration downloads.

Changes have been made to the Calibration Download interface to include Aftertreatment Doser calibrations, Next Generation Cense calibrations, and Dual Fuel calibrations. These changes can only be seen in the new QSOL3 interface. To verify that you are in the correct QSOL3 interface, please follow the steps below:

  1. If you have QSOL saved as a favorite or bookmark using the outdated URL, you willneed to delete your bookmark
  2. Enter the address
  3. Once you log in you should see following web address

The qs3 will let you know that you are in the right version of QSOL.

Cummins Insite ECM calibration download tutorial:

NOTE: It is recommended to delete or rename any intelect folder and all subfolders from the C:IntelectINSITECalibrationWorkspace directory

  1. Log in to


  1. Click on the Service tab


  1. Click on the Related Information tab


  1. Click on the Calibration Downloads link


  1. When the Calibration download screen pops up, the user has the option to select

Engine Calibration, Doser Calibration, NextGen Cense Calibration, or Dual Fuel

Calibration in the Calibration Type pull-down menu

  1. Select the correct calibration type.


  1. Enter the appropriate calibration code:
  2. For Engine Calibration downloads, enter the Engine Serial Number (ESN) and

ECM Code (without revision number) as shown


  1. For Doser Calibration downloads, enter the Doser calibration code (without

revision number). The Doser calibration code may also be referred to

as device code.


  1. For Next Generation Cense Calibration downloads, enter the Next Gen Cense

calibration code


  1. For Dual Fuel Calibration downloads, enter the Dual Fuel calibration code


  1. Click Download Zip File and the File Download window will open.
  2. Click Savewhich will save the calibration file to the Downloads folder.

Depending on the computer settings, it may be saved to a different folder.


  1. Click on Open folder which will take you to the zipped calibration file

cummins-insite-ecm-calibration-download-12 cummins-insite-ecm-calibration-download-11

  1. Right-click on the zipped calibration file. Go to Open with and then WindowsExplorer


  1. In the Extract tab, click on Extract all. In the Extract Compressed (Zipped) Folders

window, browse to C:IntelectINSITECalibrationWorkspace. Click on OK,

and then click on Extract

Note: Extract Doser calibrations to the C: or D: root drive.

cummins-insite-ecm-calibration-download-17 cummins-insite-ecm-calibration-download-14 cummins-insite-ecm-calibration-download-15 cummins-insite-ecm-calibration-download-16

  1. OpenINSITE, click on Calibration Selection, click on ECM, and then find the calibrationin the CalibrationWorkspace. If INSITE is already open in the Calibration Selection window, you will need to click on View  Refresh to refresh the screen

Note: If the C: or D: root drive has been selected previously, INSITE will display the calibration on the selected drive instead.


  1. If you do not see the ECM calibration code, go into Tools Calibration Selection

Certification Codes… and check that the correct or all certification codes are

in the right hand side window

cummins-insite-ecm-calibration-download-20 cummins-insite-ecm-calibration-download-19

Cummins INSITE ECM Calibration FAQs:

Q: Why do I keep getting a message saying “Invalid ECM code”?

A: The ESN must match the ECM calibration code family/type. For example, if the ESN is

for an ISX CM871 but the ECM Code requested is for an ISB CM2150, this message would

appear. Please verify the ESN and ECM Code.

Note: Enter the ECM calibration code without the ECM Code Revision.

Q: My module is ROM booted, how can I find the ECM Code?

A: The ECM Code and/or the SC and DO Options should be stamped on the engine

dataplate. If it is unavailable, the ECM Code may be listed on QSOL. If not, the options can

be used with an INCAL to determine the correct ECM Code.

Q: I’m not sure what revision on the ECM Code I need. Is there a way to look it up?

A: This process will provide the latest revision of the requested ECM Code. It will not

provide older revisions of ECM Codes.

Q: How often are the ECM Codes updated?

A: The ECM Codes are only revised when there is an Engineering Release to make

changes. The process will update this site for any revised calibrations on a daily basis. For

example, if an update is made on AB10001.00 today, AB10001.01 would be available


Q: How do I know what has changed in this calibration revision?

A: Please see the ECM Calibration Revision History which can be found under “My

Applications” on the side menu or as a link under the Service tab under the Related

Information tab in the Service Applications section.

Q: What if I have more questions?

A: Please submit a QSOL ticket for any questions or issues.

Insite pro:

Insite lite:

Les commentaires sont fermés.